Singapore

Membranes used in water reuse and pollution control applications are often exposed to feed solution species (e.g., proteins, polysaccharides, humic materials) that adsorb or otherwise accumulate during the filtration run, and thus can cause fouling. This has many consequences, including increased energy usage, a need for more frequent cleaning, and shortened membrane life. Here we examine novel and feed-specific hydrophilic coatings to mitigate the effects of fouling with the goal of reducing fouling resistance and energy consumption.
The coatings examined here are based on dopamine (DA), a biomimetic self-polymerizing hydrophilic material. They include DA, dopamine blended with 2-(dimethylamino)ethyl methacrylate (DAEMA) and DAEMA polymer (PDAEMA), and a novel coating using the dopamine analog norepinephrine.
The coatings containing DAEMA or PDAEMA offered anti-microbial activity, whereas the norepinephrine coatings provided very smooth hydrophilic surfaces that resisted fouling at low coating amounts, thus reducing coating resistance. These coatings were applied to commercially available 30 kDa poly(ether sulfone) membranes using a batch dip-coating method for a range of reaction times up to 3 h. 
Membranes were tested in bench-scale filtration tests using a dead-end system with mixing. Measurements included mass of permeate as a function of time, temperature, and solute concentration. From these we calculated solution flux, resistance, and energy consumption. Membranes were characterized using contact angle, atomic force microscopy (AFM), attenuated total reflectance Fourier transform infrared spectroscopy (FTIR), x-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The coatings enhanced anti-fouling properties against model foulants (BSA, SA, and SRNOM), and two treated municipal wastewaters. The modified membranes exhibited less energy consumption and lower fouling resistance as compared to as-received membranes.

MATERIALS FOR HUMANITY (MH 21)

Hydrophilic coatings for water reuse and pollution control applications

**Please view our Welcome to MH21 video.**

<center>
<figure class="video_container">
	 <iframe src="https://screencast-o-matic.com/watch/cr1UYHV1pcz?v=6&ff=1&title=0&controls=1" width=826 height=526 frameborder="0" allowfullscreen="true"> </iframe>
</figure>
	</center>


**Walkthrough Video**

Here is a Walkthrough showing how to navigate the conference and network with others 

<center>
<figure class="video_container">
	 <iframe src="https://screencast-o-matic.com/watch/cr1vnrV1paE?v=6&ff=1&title=0&controls=1" width=826 height=526 frameborder="0" allowfullscreen="true"> </iframe>
</figure>
	</center>




	 Organized by
 
<a href="https://mrs.org.sg/">
<img src="https://assets.underline.io/uploads/markdown_image/1/image/95d5789689d5f900b90e9fe54ea3cf0d.jpg"</a>

 
	
	 In association with
 
<a href="http://www.ntu.edu.sg/">
<img src="https://assets.underline.io/uploads/markdown_image/1/image/334cd171ad2fdee033c635b368e5e160.png"</a>
	<a href="https://www.nus.edu.sg/">
<img src="https://assets.underline.io/uploads/markdown_image/1/image/32e6f82c0440f7bb24c590f9f67821bd.png"</a>
		<a href="https://www.a-star.edu.sg/">
<img src="https://assets.underline.io/uploads/markdown_image/1/image/72557865b589cfa3d2a0243ffce4a270.png"</a>
	
 


	 Supported by
 
		 <a href="https://www.visitsingapore.com/mice/en/about-us/about-secb/">
<img src="https://assets.underline.io/uploads/markdown_image/1/image/6e679842ead62be522ba6a630b82d5c9.png"</a>

To access the MH 21 Conference, [please register](https://mh21.mrs.org.sg/event/da3f9651-429f-4763-81b2-ebd7311b6bc8/websitePage:206f7605-1731-41f9-8421-56d3890f398f)

MH 21 is arranged around 6 themes that focus attention on pressing needs that should be addressed to enhance the well-being of communities and provide a forum for presenting breakthrough discoveries.

technical paper

Different green technologies have been investigated in our research group in the last two decades to produce clean energy and more efficient thermal systems with the purpose to reduce the emissions of pollutants. Simulations, experiments and thermal analysis have been performed to develop and improve the efficiency of Parabolic Trough Collectors (PTC). In this type of collectors, solar radiation reflected in a parabolic surface is concentrated to heat a fluid that circulates in an absorber receiver. One of the strategies to enhance the heat transfer of the PTCs is the application of nanofluids as a working fluid. These nanofluids are produced by dispersing nanoparticles in a fluid base with the purpose to increase their thermal properties. Nanofluids with nanoparticles of Al2O3, TiO2 and graphene dispersed in water and oil have been developed and characterized by our group. These nanofluids have been experimentally tested in a PTC for real operating conditions. We have also developed a hybrid PTC with photovoltaic cells in the receiver with the objective to generate simultaneously thermal and electrical energy. The technical and economic feasibility of a plant of hybrid PTCs to satisfy part of the demand of heat and electrical energy of the industry and the building sector have been investigated for different applications, climates and economic scenarios. 
In order to reduce the energy consumption of the buildings, the application of phase change materials (PCM) in components of the envelope, such as the roof and the walls, has been studied. The purpose of these PCMs is to reduce the heat gains of the buildings and delay the maximum peak loads because the thermal energy that is transfer through the envelope of the building is used to melt the material of the PCM. Experimental and simulations results performed in different types of buildings and climates are discussed. 
Finally, it is presented a computational platform (http://www.tecsb.com) developed by our group that use satellite information of solar radiation and available roof surface of a metropolitan area to predict the solar potential for generation of electrical and thermal energy with different solar collectors technology and to estimate the reduction of energy consumption in the building due to the application of different passive technologies such as PCM, reflective paintings and insulator materials. The program has the capability to provide an estimation of the reduction of CO2 emissions due to the use of these renewable and green technologies instead of technologies that burn fossil fuels.


Applications of parabolic solar collectors, nanofluids and phase change materials to reduce pollutant emissions

Conventionally, mechanical-recycled plastics have been irreversibly deteriorated in mechanical properties due to chemical degradation accompanied by molecular chain breakage, and it has been said that they can be applied to almost one-time downgrade recycling. On the other hand, we have found that the main cause of this deterioration of mechanical properties is physical degradation due to structural deformation inside of the plastic, and it is possible to improve the mechanical properties by using self resilience ability of plastic. Furthermore, it has been clarified that the mechanical properties can be improved efficiently by using a newly designed extruder with a molten resin reservoir used when repelling waste plastic.

Self Resilience ability of Waste Plastics

Dimaleimide-substituted tetraphenylethene (TPE-2MI), which is non-emissive due to photo-induced electron transfer (PET) between maleimide (MI) and tetraphenylethene (TPE) groups, was synthesized and used to cross-link random copolymers of methyl, decyl, or lauryl methacrylate with furfuryl methacrylate. The mixture of the copolymers and TPE-2MI in DMF showed reversible fluorescence with “turn on/off” behavior depending on the Diels–Alder (DA)/retro-DA temperature adjustable process. At high temperatures, the retro-DA reaction dominates, and the fluorescence is quenched by PET mechanism. In contrast, at low temperatures, the emission recovers as the DA reaction takes over. A transparent PMFM/TPE-2MI polymer film was prepared to show an accurate response to the external temperature with tunable fluorescent “turn on/off” behavior. This study proposes possible applications in areas such as information security and transmission.

Diels–Alder Polymer Networks with Temperature-Reversible Cross-Linking-Induced Emission

Hydroxyapatite (HA) is a calcium phosphate bioreactive and biocompatible material which is an essential element for bone regeneration in human and animal bodies. HA can be found abundant in bones and shells of aquatic animals. The extraction or recovery of HA from aquatic species play an important role in future biomedical applications such as drug delivery, implant coatings, scaffolds for bone grafts, etc. [1]. Therefore, in our study, a wet chemical method was utilized for extraction of HA from bones of different types of seafood wastes (Oreochromis spp, Channa striata, Thunnus albacares, Notopterus notopterus, Salmo salar, Pangasius krempfi). The extracted HA powders were characterized by different characterization methods such as FTIR, XRD, Optical microscope and ICP-MS. Their bioactivity was also evaluated by the immersion of HA powders in stimulated body fluids. The results showed that the extracted HA powders from bones of Channa striata species had the best biocompability and be a good candidate material for bone regeneration, particularly when they existed at a nano-scaled size.

Recovery of Hydroxyapatite From Bones of Seafood Wastes and Its Bioactivity Evaluation

The increasing contamination of organic micropollutants in environmental and biological systems is one of the serious issues faced by humanity. The potentially harmful effects of organic micropollutants (pesticides, pharmaceuticals, and dyes) on human health and aquatic ecosystems have raised worldwide concerns. The releasing of organic micropollutants to freshwater causes serious health hazards because most of them are mutagenic or carcinogenic in nature. Comparing with absorbents, membrane technology possesses merits of high separation performance, low energy consumption, mild operation temperature, cost efficiency, and no cross-contamination, etc.
Here, we propose 2D covalent organic framework (COF) membranes for molecular separation. Azobenzene derivatives act as linkers, which can be photo-switched between trans- and cis-isomers by irradiation under ultraviolet (UV) or visible light. The resultant smart COF membrane has nanopores that can be switched between On- (big pores) and Off-state (small pores) valves for molecular separation. The COF membranes were tested in different organic solvents and exhibit permeances as high as 56.7 L m-2 h-1 bar-1, in the following order: acetonitrile > acetone > methanol > ethanol > isopropanol > DMF. Interestingly, the smart cis-COF membranes with Off-state valves under UV show higher rejection for dye molecules than the trans-COF analogue with On-state valves. Different from the traditional membranes with immutable pore channels, the pore size of COF membranes can be remotely tuned by controlling the trans-to-cis isomerization of azobenzene via UV/Vis light, therefore, the permeance and separation factor can be adjusted as needed.
The ingenious design strategy endows traditional membranes with new fascination and opens up new perspectives for separation science and technology. The development of COF based smart membranes with a periodic honeycomb lattice could be a promising solution for a wide variety of separations such as catalyst and solvent recycle, wastewater treatment (organic micropollutant or heavy metal removal), valuable drug purification from organic solvents in pharmaceutical industry (vitamin or antibiotic refinement), oil extraction and purification in food industry, and other challenging separations (hemodialysis or chiral pharmacology separation).

Smart light-responsive COF membrane for molecular separation

Concerns over dwindling oil reserves, carbon dioxide emissions from fossil fuel sources and associated climate change is driving the need for clean, renewable energy supplies. If average global temperature rises induced by greenhouse gases are not to exceed 1.5 °C, then estimates indicate that a large proportion of crude oil, gas and coal reserves must remain untouched.1 Biomass, derived from agricultural and forestry residues, or non-food sources of triglycerides are a sustainable source of carbon that can provide low cost solutions for transportation fuels and organic chemicals. Akin to petroleum refining, biorefining will integrate biomass conversion processes to produce fuels, power, and chemicals, thereby increasing the economic viability of bio-derived processes. Indeed, the US DoE identified a range of sugar derived ‘Platform Chemicals’ produced via chemical or biochemical transformation of lignocellulosic biomass as potential targets for manufacture in biorefineries.2 Catalytic technologies played a critical role in the economic development of both the petrochemical industry and modern society, underpinning 90 % of chemical processes and contributing to over 20% of all industrial products. In a post-petroleum era, catalysis will underpin biorefinery technology, and researchers will need to rise to the challenge of synthesising chemical intermediates and advanced functional materials and fuels from such non-petroleum based feedstocks.3 

This presentation will discuss the challenges faced in catalytic biomass processing, and highlight recent successes in catalyst design facilitated by advances in nanotechnology and careful tuning of catalyst formulation. Specific case studies will explore (i) how the effects of pore architecture and acid strength can impact upon process efficiency in biodiesel synthesis;4,5 (ii) how catalytic pre-treatments improve transportation fuel production from pyrolysis oil,6 and (iii) the role of bifunctional catalysts in the hydrodeoxygenation of phenolic components in bio-oils,7 and the aqueous phase processing of sugars to important platform chemicals and fuel precursors such as 5-HMF derivatives.8



References. 
1. M. Jakob, J. Hilaire, Nature, 517 (2015) 150.
2. J.J. Bozell, G.R. Petersen, Green Chemistry, 12 (2010) 539.
3. K. Wilson, A. F. Lee Phil. Trans. R. Soc. A, 374 (2016) 20150081.
4. A.F. Lee, K Wilson, Catalysis Today, 242 (2015) 3. 
5. M.A. Isaacs, C.M.A. Parlett, N. Robinson, L.J. Durndell, J.C. Manayil, S.K. Beaumont, S. Jiang, N.S. Hondow, A.C. Lamb, M.L. Johns, K. Wilson, A.F. Lee, Nature Catalysis, 3 (2020), 921.
6. L. Ciddor, J.A. Bennett, J.A. Hunns, K. Wilson, A.F. Lee J. Chem. Tech. Biotech., 90 (2015) 780. 
7. A. Shivhare, J.A. Hunns, L.J. Durndell, C.M.A. Parlett, M.A. Isaacs, A.F. Lee, K. Wilson, ChemSusChem, 13 (2020), 4771.
8. A. Osatiashtiani, A.F. Lee, D.R. Brown, J.A. Melero, G. Morales, K. Wilson, Cat. Sci. Tech., 4 (2014), 333. 


Catalysts for a Sustainable Future

Sulfur-containing polymer is promising to the application of the optical, anti-corrosion and antifouling materials. Using sulfur-containing C1 building blocks [i.e. carbonyl sulfide (COS), carbon disulfide (CS2)] to copolymerize with epoxides have been rapidly developed in our group and others. This talk reports two metal-free routes for the reaction of COS with epoxides.
1) The inhibition of oxygen-sulfur exchange reaction (O-S ER)1 for synthesizing poly(monothiocarbonate)s. Two types of organocatalysts will present, one is the combination of Lewis bases including amidine, guanidine, or quaternary onium salts with triethyl borane.2 A highly transparent and colorless poly(monothiocarbonate)s are obtained with > 99% tail-to-head content and high Mns of up to 92.5 kg/mol. O-S ER that would generate random thiocarbonate and carbonate units, were totally suppressed in most instances. The turnover frequency (TOF) of these Lewis pairs are as high as 240 h-1 at ambient temperature. The other is the combination of organic bases and thioureas via cooperative catalysis.3 Poly(monothiocarbonate)s are obtained with 100 % alternating degree, > 99% tail-to-head content, high Mns of up to 98.4 kg/mol and narrow molecular weight distributions (1.13-1.23). TOFs of the catalysts are up to 112 h−1 at 25 °C. 
2) The utilization of O-S ER for synthesizing poly(thioether)s using COS and epoxides as the starting materials.4 This route undergoes the coupling reaction of COS with epoxides, decarboxylative ring-opening polymerization (ROP) of the generated mixed cyclic thiocarbonates with releasing CO2(a little bit COS). And this method is also applied to the reaction of carbon disufide with epoxides, providing a new pathway to produce COS and poly(thioether)s simultaneously. 
Finally, we’ll present the transformation of poly(monothiocarbonate)s to poly(thioether)s by using O-S ER process, which is a polymer A to polymer B method for recycling the polymers.

Organocatalytic Synthesis of Sulfur-containing Polymers

Composites, and especially carbon fibre reinforced plastics (CFRP), have impressively demonstrated their mechanical performance in several applications in the last years, starting from aerospace, finding their way into sports and commodities and just recently having a significant increase in the wind energy sector. These materials are often referred to as “a material with high potential”. The question is: potential to what? The potential to be a solution to the CO2-problem due to lightweight construction capabilities and the possibility to contribute to fuel savings during the lifetime of an aircraft, a truck or a car, to provide clean energy with more efficient next-gen wind turbines? Or is it the potential to be part of the problem, as the material is very difficult to recycle and currently causes trouble in waste incineration plants and in many cases just ends up in landfills. The presented talk will address the state of the art of recycling CFRP-materials: in a first step the different components of the materials (fibres and plastics, the so called matrix) need to be separated. This can be done via pyrolysis on a commercial scale, or by different alternatives with lower TRL levels. After that the recovered fibres are processed into semi-finished products, such as nonwovens, that are suitable to replace the first-gen materials in terms of handling and processing. All along the way, it is necessary to monitor the properties of the materials, in order to be able to identify correlations of process-parameters and resulting properties, both for quality assurance in a future supply chain, as well as identification of further demand for continuing R&D-activities. Finally, the stakeholders in a circular economy are adressed: why should a company invest in the improvement of recycle-ability of their products? This discussion is not limited to CFRP-materials only, but is open to interaction with other material classes with emerging circularity.

Recycling of fibre reinforced plastics - state of the art and outlook

Flexible electronics are of critical importance for medical devices, portable electronics, smart textiles, energy storage, communication and sensor systems [1,2]. However, the lifetime of electronics is becoming shorter, which poses a growing ecological problem. Therefore, it is urgent and necessary to find sustainable and cost-efficient materials to replace the crude oil-derived polymers that are commonly used in flexible electronics. To this end, fish gelatin (FG) extracted from fish scales could provide an eco-friendly and biodegradable alternative to plastic for use in flexible electronics. Fish scales are inedible and malodorous kitchen waste, and >2 million metric tons of fish scales are discarded each year. This talk will introduce our recent works on FG-based flexible electronics, including flexible electroluminescent devices and triboelectric nanogenerators (TENGs) [3-6]. The properties of FG films, the structure design and the performance of flexible electronic devices will be briefly discussed. These works may pave a new way to green and sustainable flexible electronics.

References
1. S. Xu, A. Jayaraman, J. A. Rogers. Skin sensors are the future of health care. Nature, 2019, 571, 319-321.
2. G.-H. Lee, H. Moon, H. Kim, G. H. Lee, W. Kwon, S. Yoo, D. Myung, S. H. Yun, Z. Bao, S. K. Hahn. Multifunctional materials for implantable and wearable photonic healthcare devices. Nat. Rev. Mater., 2020, 5, 149–165.
3. X. P. Zhang, T. Y. Ye, X. H. Meng, Z. H. Tian, L. H. Pang, Y. J. Han, H. Li, G. Lu, F. Xiu, H. D. Yu, J. Q. Liu, W. Huang. Sustainable and transparent fish gelatin films for flexible electroluminescent devices. ACS Nano, 2020, 14, 3876-3884.
4. T. F. Jiang, X. H. Meng, Z. Zhou, Y. Y. Wu, Z. H. Tian, Z. D. Liu, G. Lu, M. Eginlidil, H. D. Yu, J. Q. Liu, W. Huang. Highly flexible and degradable memory electronics comprised of all-biocompatible materials. Nanoscale, 2021, 13, 724-729.
5. Y. J. Han, Y. F. Han, X. P. Zhang, G. Lu, H. D. Yu, W. Huang. Fish gelatin-based triboelectric nanogenerator for harvesting biomechanical energy and self-powered sensing of human physiological signals. ACS Appl. Mater. Interfaces, 2020, 12, 16442-16450.
6. Q. Z. Sun, H. C. Wang, L. Wang, X. P. Yue, L. R. Zhang, G. Z. Ren, D. H. Li, Y. J. Han, L. L. Xiao, G. Lu, H. D. Yu, W. Huang. Fully sustainable and high-performance fish gelatin-based triboelectric nanogenerator for wearable movement sensing and human-machine interaction. Nano Energy, in revision.

Sustainable Flexible Electronics Based on Fish Gelatin

Chitin is the second most abundant biopolymer, after cellulose. It is present in the shell of crustaceans, in the cuticle of insect and even in some fungi. Chitin can be converted into chitosan, a highly praised material in the biomedical sector for its antibacterial properties, which finds also important application as a fertilizer, water treatment flocculant and food additive. Yet today's technologies for chitosan production from biomass rely on the use of corrosive treatments, high energy input and large quantities of by product effluents. Herein we are presenting our group's effort to tackle this question. We showed that mechanochemistry and aging could be used effectively for the deacetylation of chitin.1 This process yielded high molecular weight chitosan with minimal use of energy and solvent. This method is versatile and applicable to a number of chitin sources, including crude crustacean and insect shells, yielding deacetylation up to 98% and remarkably high molecular weights. This process affords chitosan in a safer fashion and with less materials and energy usage compared to the classic hydrothermal one. We have also extended this method to the fabrication of chitosan nanocrystals from chitin nanocrystals.2 Chitin and chitosan nanocrystals featured enhanced properties are nanocatalysts supports.3,4 We have also developed hydrogels from chitosan and chitin nanocrystals, with exceptional gelling properties and demonstrated their applicability for slow drug release.

Premium content

Downloads

Next from MATERIALS FOR HUMANITY (MH 21)

Applications of parabolic solar collectors, nanofluids and phase change materials to reduce pollutant emissions

Similar lecture

Perspectives of sustainable development, life cycle and end of life in polymeric membranes